Service

Electrical design

We produce drawings the cabinet builder and the installer can work from without asking questions. And at the end they show what was actually built — not what was planned at the start.

  • Wiring diagrams
  • Cabinet layout
  • Cable and terminal lists
  • 3D cabinet design
  • Exploded view · BOM

When people get in touch

The situations we
usually meet

A new cabinet is being built

The builder needs a drawing set they can assemble from without asking questions.

  • Power and control wiring diagrams
  • Cabinet layout and device schedule
  • Cable and terminal lists

The existing drawing does not match reality

Over the years things were rewired and extended, but the documentation never followed.

  • On-site survey and a survey report
  • Wiring diagrams and I/O tables put in order
  • Documentation turned into an as-built set

An extension or a rebuild is coming

New equipment is arriving, and you need to know in advance whether it fits and what has to be replaced for it.

  • Load and protection review in the design
  • Space and spare capacity checked
  • 3D layout to catch clashes
Rows of contactors in a control cabinet, with device identification labels
Devices inside the cabinet — every switch with its own identifier, exactly as it appears on the drawing and in the schedule

What the work involves

What the design
documentation contains

Wiring diagrams

Power and control drawings with consistent marking and identifiers.

  • Supply, protection, motor starters
  • Control circuits, interlocks
  • PLC I/O wiring with signal identifiers

Lists and schedules

Purchasing and the installer work from these — which is why they are produced together with the drawings.

  • Device schedule with types
  • Cable list with cross-section and length
  • Terminal and connection list

3D cabinet design

A three-dimensional layout of the cabinet and the panels before manufacturing.

  • Clash checking and installation clearances
  • Cable duct and mounting arrangement
  • Exploded view with a BOM
  • Manufacture-ready documentation and visualisation

What you receive at handover

  • The complete drawing set in PDF and in an editable source format
  • Device schedule, cable list and terminal list
  • Construction drawings, then an as-built set after installation
  • A description of the protection concept

For the as-built set, changes made during installation have to be reported back to us — we put that in the agreement.

Why SKY SOL

Why it is worth
calling us

Ten years in the field

The team has spent ten years in industrial environments: programming, commissioning, fault finding. We do not know machines from textbooks.

One engineer, start to finish

The same person surveys the job, writes the program and commissions it. You never have to explain the same thing twice, and nothing is lost in a handover.

The source code is yours

The program backup, the I/O list and the operating instructions are part of the handover, not a separately priced item. The system does not tie you to us.

Drawings you can build from

We issue the design so that the cabinet builder can work from it without asking questions, and so that at the end it shows what was actually built.

Boundaries

Where our work
ends

Scope — what we do not take on

Clear boundaries

The electrical and control design comes from us: we produce it with our design partner, and we carry the technical content and the coordination. Cabinet manufacturing, on-site electrical installation and statutory compliance inspection are not work we take on.

Why this is good for you

The design is drawn up by people who also understand installation, and the responsibility of each trade stays where it belongs.

FAQ

What people
usually ask

Do you also manufacture the control cabinet?

No. We provide the design — produced with our design partner; cabinet manufacturing and on-site electrical installation are done by a specialist contractor. The documentation is prepared so the builder can work from it directly, and we do take on the coordination.

In what format do I receive the drawings?

In printable PDF and in an editable source format, together with the lists. That way a later extension does not have to be drawn from scratch — and the documentation is not tied to us.

What is an as-built drawing set, and why does it matter?

Construction drawings show how it should be built. The as-built set shows how it actually was built. During installation the two almost always diverge. If the as-built set is skipped, the next fault-finding job starts from the wrong drawing.

Is an on-site survey needed?

For an extension, or for replacing missing documentation, usually yes — reality and the old drawing rarely agree. For a new cabinet, a description of the process and the device list may be enough.

We only need our existing drawings updated. Is that something you do?

Yes, that can be a job on its own. After an on-site survey we put the wiring diagrams, the I/O tables and the device schedule in order.

Do you produce mechanical designs as well?

We do not draw them ourselves, but we can have them produced. For mechanical design we work with a contracted design partner, so the electrical and the mechanical design come from one place and the coordination still stays with us.

Get a quote

Let us look at
the task

Describe in a few sentences what you need solved. We reply within one working day and tell you what we need in order to quote.

Phone+36 30 463 32 43 E-mailinfo@skysol.hu
Registered officeSKY SOL Kft. · Római körút 23.
6723 Szeged, Hungary — we work nationwide
What helps us quoteA description of the process, an I/O list or an estimated signal count, any existing wiring diagrams, the platform and the deadline.

To speed up the technical discussion, tell us the PLC/HMI type, the estimated I/O count, a short description of the task, the location and the deadline you need. You can send an I/O list or technical documentation to info@skysol.hu.

Fields marked are required. We reply within one working day. You can also write to us directly: info@skysol.hu